IHXB01xUHR - Ultra Heavy Raw Beatle Busters

[Giles]

I could, but I'd prefer 34…..

[Dion]

Inbound: I hope I can make the famous BB-cut work…

[Giles]

The DWC-UHR version are on 'Special' at USD235

[Dion]

After a lukewarm ~4 hour soak/30° C wash they were perfect in size but stretched out almost back to the raw-measurements. The only noticeable shrinkage was the inseam (1,18 inches loss). No leg-twist/skewing. Will a really hot soak shrink them permanently since they are too big in the raw-state?

[Cole]

Today I received a IHxB01-UHR in size 34. I hope the Buster cut works for me. In the raw unsoaked state it feels a little wide in the legs, but that may be because I'm used to the 666LB and the 461S, which both have tighter legs.

Right now it is in the bathtub for a 30° soak.

And after that it will definetly need to be hemmed I guess. I'm not so much into cuffs or double cuffs.

Meassurements before the soak:

Waist: 88 cm
Front rise: 30 cm
Rear rise: 39 cm
Tights: 31,5 cm
Knee: 23 cm
Hem: 22 cm
Inseam: 94 cm

[T.J.]

Pre soak fit looks good.. I've got my requested fit after two hot soaks and a 30 Degrees Wash in the washing machine..

[Appfaff]

@Cole - those looks really good pre-soak

My 666 UHR were a lot looser than that pre-soak and slimmed up a lot in the legs after a few soaks and washes.

[Dion]

The first ~4 hour soak/30° C wash didn't do much to mine, they softened up and stretched back immediately to their raw-measurements. After another really really hot 1 hour soak they shrank a bit and feel definitely more like 23 oz now. I hope they don't stretch back. And the UHR-denim is simply amazing.

[Appfaff]

^ it took me 3 soaks + washes to get mine to give in. 1 cold soak and cold wash/no spin - second hot soak + warmish wash/no spin - then finally a 2 hour super hot soak and a hot wash on the "towels" setting for max agitation.

[Cole]

Pre soak and pre wash I though it was doable to break it in without to much trouble, but post soak and post wash (40° C) it feels as stiff as cardboard or thin wood. This is going to get interesting. I think I'm a little afraid. 

[Dion]

Did you get much shrinkage, Cole?

[Cole]

@den213:

Did you get much shrinkage, Cole?

I'll take measurements tonight, @den213 (if I'm still alive by then, after the 101tg incidient that is going to happen). 

[Dion]

You have the whole IH-forum on your side and tell her it's simply the replacement for the one you sent back last year!

(from the Standing Denim thread):

[JCMx800]

@Cole:

Pre soak and pre wash I though it was doable to break it in without to much trouble, but post soak and post wash (40° C) it feels as stiff as cardboard or thin wood. This is going to get interesting. I think I'm a little afraid. 

Haha yeah, the 21/23 hardcore after the first wash. And it don´t get better

[T.J.]

^so true [emoji6]

[Cole]

Still alive. 

Meassurements before the soak:

Waist: 88 cm
Front rise: 30 cm
Rear rise: 39 cm
Tights: 31,5 cm
Knee: 23 cm
Hem: 22 cm
Inseam: 94 cm

Meassurements after soak and 40°C wash:

Waist: 84 cm (-4 cm)
Front rise: 30 cm
Rear rise: 37 cm (-2 cm)
Tights: 30cm (-1,5 cm)
Knee: 23 cm
Hem: 22 cm
Inseam: 90 cm (-4 cm)

[steelworker]

My favorite denim with my new favorite cut. IH doesn't disappoint.

[Cole]

Post soak fit pics. The back shot and side shot where blurry and I have no time to redo them at the moment.

can do a single cuff now, instead of the pre soak double cuff. After another wash or two they will go off to heming.

[T.J.]

That's a great fit.. But it will time to break in [emoji6]

[ROman]

UHR denim is by far my favorite. As of right now, the IHXBO1XUHR, and the 1955UHR, are my favorite jeans. Not in that particular order. I haven't done a soak on them, just regular wash, low spin, minimal shrinkage. My biggest problem is usually doing or undoing the buttons. Now I gently use needle nose pliers.